portant; margin-bottom: 20px !important; width: auto !important; line-height: 2em !important;">portant; margin-right: 0px !important; margin-left: 0px !important; width: auto !important;">1. 試驗目的：針對PCB使用環境有可能在海上或海邊等空氣中含鹽度較高的地區，因耐鹽度較差會(huì )影響其功能，嚴重時會(huì )導致重大事故,通過鹽霧試驗來驗證產品是否產生腐蝕現像。鹽霧實驗分中性鹽霧（NSS）、乙酸鹽霧（AASS）、銅加速乙酸鹽霧（CASS）試驗等,中性鹽務試驗適用于金屬覆蓋層、有機覆蓋層等，其它兩種適用于銅+鎳+鉻等裝飾性鍍層。

portant; margin-bottom: 20px !important; width: auto !important; line-height: 2em !important;">portant; margin-right: 0px !important; margin-left: 0px !important; width: auto !important;">2.引用標準

portant; margin-bottom: 20px !important; width: auto !important; line-height: 2em !important;">portant; margin-right: 0px !important; margin-left: 0px !important; width: auto !important;">2.1 GB/T2423.17-1993 電工電子產品基本環境試驗規程試驗Ka：鹽霧試驗方法；

portant; margin-bottom: 20px !important; width: auto !important; line-height: 2em !important;">portant; margin-right: 0px !important; margin-left: 0px !important; width: auto !important;">2.2 GJB 軍用設備環境試驗方法鹽霧試驗；

portant; margin-bottom: 20px !important; width: auto !important; line-height: 2em !important;">portant; margin-right: 0px !important; margin-left: 0px !important; width: auto !important;">2.3 GB/T 金屬基本體上金屬和其它無機覆蓋層經腐蝕試驗后的式樣和試件的評級；

portant; margin-bottom: 20px !important; width: auto !important; line-height: 2em !important;">portant; margin-right: 0px !important; margin-left: 0px !important; width: auto !important;">2.4 ISO Corrosion of metals and alloys——accelerated testing involving cyclic exposure to salt mist,” dry” and“wet” condition

portant; margin-bottom: 20px !important; width: auto !important; line-height: 2em !important;">portant; margin-right: 0px !important; margin-left: 0px !important; width: auto !important;">3.中性鹽霧試驗方法：

portant; margin-bottom: 20px !important; width: auto !important; line-height: 2em !important;">portant; margin-right: 0px !important; margin-left: 0px !important; width: auto !important;">在電導率不超過20μs/cm的蒸餾水或去離子水中配制成含有5%+/-0.1%的氯化鈉溶液，PH值 6.5-7.2，

portant; margin-bottom: 20px !important; width: auto !important; line-height: 2em !important;">portant; margin-right: 0px !important; margin-left: 0px !important; width: auto !important;">在溫度35+/-2度，濕度85%以上，以壓力0.7-1.8kgf/cm2，噴霧量1.0-2.0ml/80 cm2/h連續噴霧24小時（具

portant; margin-bottom: 20px !important; width: auto !important; line-height: 2em !important;">portant; margin-right: 0px !important; margin-left: 0px !important; width: auto !important;">體時間需客戶指定），鹽霧箱中樣品按30度角放置，試驗結束后30分鐘以?xún)?，將樣品從鹽霧箱中取出，

portant; margin-bottom: 20px !important; width: auto !important; line-height: 2em !important;">portant; margin-right: 0px !important; margin-left: 0px !important; width: auto !important;">為了減少腐蝕產物脫落，試樣應先在室內空氣中自然干燥0.5h~1h；然后用溫度不超過35℃的干凈流動水

portant; margin-bottom: 20px !important; width: auto !important; line-height: 2em !important;">portant; margin-right: 0px !important; margin-left: 0px !important; width: auto !important;">將被測試樣小心清洗，以去除試樣表面殘留的的鹽霧溶液，接著以距試樣30cm處壓強不超過200Kpa的

portant; margin-bottom: 20px !important; width: auto !important; line-height: 2em !important;">portant; margin-right: 0px !important; margin-left: 0px !important; width: auto !important;">空氣吹干，檢查樣品